"Unconventional" SCIENCES and NEW DISCOVERIES > All FREQUENCIES

How to build your own RIFE FREQUENCY GENERATOR (quite easy)

(1/1)

PiJo:
         


      BUILD YOUR OWN RIFE FREQUENCY GENERATOR



               



STEPS :

1 - Check for the Rife Frequencies HERE or DOWNLOAD HERE (PDF)

Other link : The All-Frequencies CAFL (AFCAFL)


IMPORTANT NOTE : all RIFE Frequencies must be used with one 3.1Mhz (3100000 Hz) Carrier Frequency to be efficient.
Just add this frequency to all of the Rife Frequencies you want to use (inside your Frequency Generator software).


2 - Download FREE Frequency Generator software :

Frex software :

FreX16 - Popular "Flag Ship" single channel high performance software : HERE

FreXmcm - 8 Channel Sweep Function software and Dual instrument control :   HERE

CHIamp - Low Frequency, unique frequency streams directly assists balancing the CHI energy waves. Inspired by the Infratonics instrument : HERE

Website : http://www.frex.com.au/
FreX - Frequency Database : https://www.rife.de/frex-frequency_database.html
Welcome to FreX - Help & Tips : https://www.scribd.com/document/268339185/Welcome-to-FreX


Multi Wave Frequency Generator 1.2 (2.1 MB) : HERE

Blaster 5 (39.8 KB) : HERE

Digital Signal Generator (66.6 KB) : HERE

Dr. Rife Frequency Generator [Installer] (559 KB) : HERE

Frequency Generator [Installer] (346 KB) : HERE

Marchand Function Generator (27.2 KB) : HERE

MultiSine (617 KB] : HERE

NCH Tone Generator (344 KB] : HERE or HERE (latest version)

Test Signal Wave Generator (107 KB) : HERE



3 - The SET-UP :   

(Author's page : http://www.noriftrife.com/tutorials.asp )
   

                   

IMPORTANT NOTE : before using the frequency generator software please reduce the volume level of your computer to avoid damaging the internal speakers.



- Open the frequency generator software


                   
                                   Example



- Enter the frequencies you chose (don't forget to add the 3.1Mhz Carrier Frequency)

- Connect the amplifier (minimum 15 Watts RMS, 35 Watts RMS recommended).
To convert PMPO Watts to RMS, divide the number of PMPO Watts by 15 (it is an approximation ratio).



                   


1.  Stereo-to-RCA connector :  In the illustration above this is the connector that plugs into the headphone output on the laptop.  You can use the speaker output or headphone output on your desktop or laptop.  The other end (RCA connectors) plugs into the amp input (stereo aux input) with L(eft) and R(ight) channels).  One side is red (the +) and the other is white (the ground). 
Use only one channel (left or right) if you only want to run two electrodes (one connected to the + output, one connected to the Ground output).  Use both the 2 red and 2 white if you want to run 4 electrodes.

2.  If you need a mini amp my choice is the Pyle Pro 2 x 40W (around $60), the power input to the amplifier is on left side (see illustration above.)  The power adapter in the illustration powers the mini amp.  Always turn the volume all the way down before connecting and then gradually turn up the volume till you feel a tingle.

3.  If you are using your own amplifier, it must have a sound input, and a sound output.  Most amplifiers have a volume control.   Our Mini amp is controlled by the computer volume control alone.  This is usually in the bottom right hand of the computer screen in the form of a speaker icon.  Remember to turn up the volume on the computer if you have your own amplifier with a volume control.




- Connect the electrodes (rods, tubes, plates, pads, ...). Stainless steel highly recommended.


             
                          Electrodes

 1.  In the illustration above we have connected two electrodes.  If you were connecting a speaker, this would be the two wires that connect to the speaker.  The beige wire is called the lead wire and connects to the electrodes (one on the +, one on the Ground). 

2.  There are still two connections for output #2 on the amplifier.  If you want to connect 4 electrodes, just connect another lead wire and two more electrodes as illustrated.

There are many amplifiers online.  The one we use is called "Pyle Pro Mini 2x40W"   Just do a search online to find the amplifier.





                   
                           Electrode covers

1.  This is a picture of the electrode covers (blue).   Just look for wrist sweat bands online.

2.  The Electrode covers will slide over the stainless steel electrodes.  Moisten the covers in warm water (add a little salt to the water for better conductivity).  Slide the covers over the electrodes and do not allow the electrodes to touch each other.




                   
                          Alligator clips attached to the copper tubes

This is a picture of a setup using hardware from local stores.  The copper wire is speaker wire from Radio Shack, the copper tubes are 4" x 1" from the local hardware store.  Just strip the ends of the speaker wire and attach alligator clips and clip the other end into the amp as if you are hooking up one speaker.

The Black wire is an RCA connection to the input of the amplifier and the other end is a common stereo plug that plugs into the output of the computer headset. 





                 
                          Back of Amplifier

This is is a close-up and as you can see the RCA red and white go to the input of the amplifier and the copper speaker wires are hooked up to the output of the amplifier (and are connected to the copper tubes at the other end).





                 
                       When everything is ready




PLASMA TUBES


         


The basics of a "Rife" machine are simple: An argon or helium plasma tube, excited by some form of high voltage, is modulated by audio modulations. Many theorize that it is the extremely high-harmonics of those modulations that, in some way, disrupts the cellular structure of various pathogens. The original Rife Ray machine used a helium plasma lamp, which was a used X-ray tube which had been filled with helium instead of having a high vacuum (there were NO X-rays from the tube when tested by an independent testing lab; X-rays being impossible at the voltages used for the Rife tubes, and with a low-pressure gas in the tube. X-Rays require very high voltages AND a very high vacuum.) Most experimenters use either short straight tubes available from many sources, and usually filled with argon, helium, or an argon-neon mixture, or a Phanotron tube, which somewhat resembles an old-style X-Ray tube. Straight tubes are available for around $100 US, while the Phanotrons usually cost more than twice that. (It is important to note that no X-Rays are generated from these devices; X-Rays require high voltages and hard vacuum for their generation.) The Phanotron is a bubble tube with electrodes, and seems to produce a more directional emission of the Rife effect. Some experimentors are using other gasses as well. Rife's original notes alternately said that he used helium and also argon.

In the Bare-Rife machine, an audio frequency generator (sometimes replaced by a personal computer running special frequency-generating programs) is used as the audio input to a high-voltage radio-frequency source. That modulated output is amplified, and "tuned" or coupled into an argon or other noble gas (helium etc) tube running a partial vacuum, just like a fluorescent tube or camera's flash lamp. When done properly, the tube will energize when the high-voltage source is turned on, and is modulated at audio frequencies as selected by the operator. Tuned properly, nearly all the energy is absorbed by the plasma lamp, and very little is radiated from the equipment.


If you want to add a PLASMA TUBE to your system (as on the original Rife Machine) and need more information, you can visit this link : http://billsplasmatubes.com/

email : bill@billsplasmatubes.com
toll free number : (855) 538-4992 (USA and Canada residents only)




-----------------------------------------------------------------------------------------------------------------------------------------




Another similar setup (with details) is here : http://www.introductiontorife.com/brt_contact_devices.html


         




-----------------------------------------------------------------------------------------------------------------------------------------



Useful links :

Dr. Rife and Philip Hoyland with a 1938 Beam Ray Machine
http://rifevideos.com/dr_rifes_true_original_frequencies.html

Hulda Clark Frequencies
http://www.electroherbalism.com/Bioelectronics/FrequenciesandAnecdotes/Hulda_Clark_Frequencies.htm

How to make any frequency generator a Rife Machine
http://rifevideos.com/how_to_make_any_frequency_generator_a_rife_machine.html

How to Build Your Own Rife Machine or TENS Unit
http://eternalspiralbooks.com/how-to-build-your-own-rife-machine-or-tens-unit/

Frequencies and Anecdotes
http://www.electroherbalism.com/Bioelectronics/FrequenciesandAnecdotes/

Some Good Rife & Related Links :
http://billsplasmatubes.com/links.html

http://rifehealth.co.za/Rife-Frequencies/

DIY Bench Tools: Build a Signal Generator
https://diyhacking.com/diy-bench-tools-build-signal-generator/

Information on FREQUENCY MACHINES, Rife technology, EMEM devices, Plasma Lamp machines and Directory / Links to Rife and Rife - Bare sites
http://www.dfe.net/links_rb.html

Purchase a REAL RIFE MACHINE here :
https://www.spooky2.com/transmission/plasmamode/













Navigation

[0] Message Index

It appears that you have not registered with NEEEEEXT. To register, please click here...
Go to full version